These surfboards are not foamies, but yes they are soft ----- And they are, in fact, very hard....10 hours more labor than most make --------- CUSHSURFBOARDS@GMAIL.COM

WAXLESS SILICONE GRIP KIT --- soft grippy no wax solution
WAXLESS SILICONE GRIP KIT --- soft grippy no wax solution
WAXLESS SILICONE GRIP KIT --- soft grippy no wax solution
WAXLESS SILICONE GRIP KIT --- soft grippy no wax solution

WAXLESS SILICONE GRIP KIT --- soft grippy no wax solution

Regular price
Sale price

We've tried them all.  From Astrodeck in the 80s to Hexa Traction---there have been many attempts to make the ultimate waxless traction.  Surfco Hawaii has done it.  We have been riding this WAXMAT grip on our boards for 2 years.  We manufacture our production boards equipped with the grip.   We have no need for wax anymore.   The WaxMat Honeycomb kits are a great way to start your waxless adventure.

This Honey Comb Wax Mat kit contains (11) full 6" x 6" panels and (2) half 3" x 6" panels.

NOTE: This kit is comparable to the 6'0" kit or 2 mid panels.

Number of kits needed to cover a board:
Shortboard: (1) kit
Funshape: (2) kits
Mini Tank: (3) kits
Longboard: (4) kits for deck only or (5) kits for full deck
SUP Nose: (1) kit
SUP Progressive Deck: (3) kits

Wax Mats have an excellent wet grip and is non-abrasive to the skin. May be used on the decks of surf, skimboards, marine crafts, bathtubs and any where an excellent slip resistant, non-abrasive, see-through surface is needed.


  • Excellent wet grip
  • Grips like wax
  • Non-abrasive to the skin
  • Will not melt, no mess
  • Works well in all water temperatures
  • Will not yellow
  • Thin see through die-cut panels
  • Easy-to-apply peel and stick adhesive
  • Cleans up with soap and water
  • Can be used with see-through Hot Grip tail pads

1. Use fresh water to wash off any sand, salt, or dirt on the board. Dry board with a towel or rag.
2. Use a wax scraper or liquid wax remover to remove wax off the deck that will be covered by the wax mats.
3. Be sure the surface is completely dry and clean of any dirt, wax, water, etc. Wipe with isopropyl alcohol if necessary.

New and Clean Board Application
Note: Proper installation of the mats takes about the same amount of time as it takes to rub on a good coat of wax. Best not to be in a hurry.
1. Select desired locations and positions of the mats on the deck. A space of up to 1" between mats is fine. If the board does not have a stringer or center line, lay a strip of masking tape down the center of the deck as a guide.
2. Board temperature must be above 65 degrees Fahrenheit for adhesive to bond to the deck.
3. Peel off 3"-4" of the liner at the end of the mat and press onto the deck. Peel off the rest of the liner and press the mat onto the deck. The mat can be lifted up and repositioned if necessary.
4. Press the entire mat firmly onto the board.
Note: Use the end of a ruler, putty knife, wax scraper, or roller, and firmly press the mat onto the board as the liner is peeled off the adhesive. This prevents bubbles from forming under the panel.
5. Repeat process to the rest of the mats.

Care and Maintenance
The Wax Mats can be cleaned with dishwashing detergent and scrub brush. Rinse with fresh water. Avoid applying or using solvents such as paint thinner, acetone or zylene, on the Wax Mats.